Inter VLAN Routing

00.

Quick Reference: Understanding VLANs

A VLAN is a switched network that is logically segmented by function, project team, or application, without regard to the physical locations of the users. VLANs have the same attributes as physical LANs, but you can group end stations even if they are not physically located on the same LAN segment. Any switch port can belong to a VLAN, and unicast, broadcast, and multicast packets are forwarded and flooded only to end stations in the VLAN. Each VLAN is considered a logical network, and packets destined for stations that do not belong to the VLAN must be forwarded through a router or a switch supporting fallback bridging, as shown in Figure 13-1. Because a VLAN is considered a separate logical network, it contains its own bridge Management Information Base (MIB) information and can support its own implementation of spanning tree. Source


						
01.

Configuring hostnames

Network Diagram of the Lab (Without DIR655 Router)

 
Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#hostname cloud20
cloud20(config)#end

02.

Enable Routing

This enables the L3 switch capable of routing.


cloud20#enable
cloud20#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud20(config)#ip routing
cloud20(config)#end

03.

Verify routing enablement.

Check the configuration and look for 'ip routing' in running-configuration


#Verify routing is enabled.

cloud20#show running-config
Building configuration...

Current configuration : 1319 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cloud20
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
system mtu routing 1500
ip subnet-zero
ip routing
!
!
!
!

04.

Static IP Address

Configure the static ip address.


cloud20#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.

cloud20(config)#interface fastEthernet0/2
cloud20(config-if)#no switchport
cloud20(config-if)#ip address 192.168.2.20 255.255.255.0
cloud20(config-if)#no shutdown
cloud20(config-if)#end

05.

Static Route

Add static route with the gateway ip/R7000v2


 
cloud20(config)#ip route 0.0.0.0 0.0.0.0 192.168.2.1

#Verify the connectivity
cloud20#ping 8.8.8.8

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/11/17 ms

06.

Configure the VLAN

Configure VLAN with the RFC1918 IP address. Subnet


baburaj@Aurora-4:~\> ipcalc 10.32.0.0/11
Address:   10.32.0.0            00001010.001 00000.00000000.00000000
Netmask:   255.224.0.0 = 11     11111111.111 00000.00000000.00000000
Wildcard:  0.31.255.255         00000000.000 11111.11111111.11111111
=>
Network:   10.32.0.0/11         00001010.001 00000.00000000.00000000
HostMin:   10.32.0.1            00001010.001 00000.00000000.00000001
HostMax:   10.63.255.254        00001010.001 11111.11111111.11111110
Broadcast: 10.63.255.255        00001010.001 11111.11111111.11111111
Hosts/Net: 2097150               Class A, Private Internet


cloud20#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.

cloud20(config)#interface vlan12
cloud20(config-if)#ip address 10.32.0.1 255.224.0.0
cloud20(config-if)#no shutdown
cloud20(config-if)#end
cloud20#

07.

VLAN to SwitchPort

Assign VLAN to Port.


cloud20#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud20(config)#interface fastEthernet0/12
cloud20(config-if)#switchport access vlan 12

08.

Interfaces/Routes.

Verify interfaces and routes.



cloud20#show ip interface brief
Interface              IP-Address      OK? Method Status                Protocol
Vlan1                  unassigned      YES manual up                    down
Vlan12                 10.32.0.1       YES manual up                    up
FastEthernet0/1        unassigned      YES unset  down                  down
FastEthernet0/2        192.168.2.20    YES manual up                    up
FastEthernet0/3        unassigned      YES unset  down                  down
...

FastEthernet0/12       unassigned      YES unset  up                    up

...


#Check the route.

cloud20#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 192.168.2.1 to network 0.0.0.0

     10.0.0.0/11 is subnetted, 1 subnets
C       10.32.0.0 is directly connected, Vlan12
C    192.168.2.0/24 is directly connected, FastEthernet0/2
S*   0.0.0.0/0 [1/0] via 192.168.2.1

09.

Server/Port Reachability.

Change the interface IP address on the target server and restart network service.



root@mayura:/etc/sysconfig/network-scripts\> ip addr show enp7s0
2: enp7s0:  mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 00:1f:bc:02:6f:10 brd ff:ff:ff:ff:ff:ff
    inet 10.32.0.20/11 brd 10.63.255.255 scope global enp7s0
       valid_lft forever preferred_lft forever
    inet6 fe80::21f:bcff:fe02:6f10/64 scope link
       valid_lft forever preferred_lft forever

#Verify the IP is reachable.

cloud20#ping 10.32.0.10

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.32.0.10, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

#Since the default route is on the GTWY IP, add a static route on the interface assigned with the IP.
ip route 10.0.0.0 255.224.0.0 10.32.0.20
 
#Verify the reachability via ping.
cloud20#ping 10.32.0.20

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.32.0.20, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms

root@mayura:/etc/sysconfig/network-scripts\> ping 10.32.0.1
PING 10.32.0.1 (10.32.0.1) 56(84) bytes of data.
64 bytes from 10.32.0.1: icmp_seq=1 ttl=255 time=1.44 ms
64 bytes from 10.32.0.1: icmp_seq=2 ttl=255 time=1.38 ms

#Save configuration 
cloud20#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]


10.

Cloud10-L3 Switch Configuration

Steps in high-level for Cloud10, similar to above for most part.


baburaj@Aurora-4:~\> ipcalc 10.16.0.0/12
Address:   10.16.0.0            00001010.0001 0000.00000000.00000000
Netmask:   255.240.0.0 = 12     11111111.1111 0000.00000000.00000000
Wildcard:  0.15.255.255         00000000.0000 1111.11111111.11111111
=>
Network:   10.16.0.0/12         00001010.0001 0000.00000000.00000000
HostMin:   10.16.0.1            00001010.0001 0000.00000000.00000001
HostMax:   10.31.255.254        00001010.0001 1111.11111111.11111110
Broadcast: 10.31.255.255        00001010.0001 1111.11111111.11111111
Hosts/Net: 1048574               Class A, Private Internet

#Configure hostname,enable routing,add static routes.
Refer steps for cloud20 (above)

#Configure static routing.

cloud10#configure terminal
cloud10(config)#interface fastEthernet0/1
cloud10(config-if)#no switchport
cloud10(config-if)#ip address 192.168.2.10 255.255.255.0
cloud10(config-if)#no shutdown
cloud10(config-if)#end
cloud10#

#Configure VLAN10

cloud10(config)#interface vlan10
cloud10(config-if)#ip address 10.16.0.1 255.240.0.0
cloud10(config-if)#no shutdown
cloud10(config-if)#end
cloud10#

#Assign port to VLAN.
cloud10#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud10(config)#interface fastEthernet0/10
cloud10(config-if)#switchport access vlan 10
cloud10(config-if)#end

#Add static route with next-hop for 10.* subnet via backend interface.
cloud10#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud10(config)#ip route 10.0.0.0 255.224.0.0 10.16.0.10
cloud10(config)#end

cloud10#ping 8.8.8.8

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/11/17 ms
cloud10#ping 10.16.0.10

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.16.0.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/8 ms



11.

Reference of Subnets

How the subnets were chosen!

baburaj@Aurora-4:~\> ipcalc 10.0.0.0/8 -s 1000000
Address:   10.0.0.0             00001010. 00000000.00000000.00000000
Netmask:   255.0.0.0 = 8        11111111. 00000000.00000000.00000000
Wildcard:  0.255.255.255        00000000. 11111111.11111111.11111111
=>
Network:   10.0.0.0/8           00001010. 00000000.00000000.00000000
HostMin:   10.0.0.1             00001010. 00000000.00000000.00000001
HostMax:   10.255.255.254       00001010. 11111111.11111111.11111110
Broadcast: 10.255.255.255       00001010. 11111111.11111111.11111111
Hosts/Net: 16777214              Class A, Private Internet

1. Requested size: 1000000 hosts
Netmask:   255.240.0.0 = 12     11111111.1111 0000.00000000.00000000
Network:   10.0.0.0/12          00001010.0000 0000.00000000.00000000
HostMin:   10.0.0.1             00001010.0000 0000.00000000.00000001
HostMax:   10.15.255.254        00001010.0000 1111.11111111.11111110
Broadcast: 10.15.255.255        00001010.0000 1111.11111111.11111111
Hosts/Net: 1048574               Class A, Private Internet

Needed size:  1048576 addresses.
Used network: 10.0.0.0/12
Unused:
10.16.0.0/12
10.32.0.0/11
10.64.0.0/10
10.128.0.0/9

Trunk/SVI Configuration

00.

Configuration steps for VLAN2 (SVI), trunked on fa0/13, One Subnet -> 10.0.1.0/24

Network Diagram of this configuration.

VLAN logically creates broadcast domains on the L2 network, so a switch can send traffic only within the same broadcast domain, in otherwords one VLAN. To communicate to devices in other broad cast domain essentially a router is required. Switch Virtual Interface is nothing but acts on Layer-3 to get this routing done, so that an inter VLAN routing is possible. So VLAN on L2 layer keeps traffic within its own broad cast domain, but to send the traffic to other VLAN's a mechanism is required to route the traffic between these two VLAN's on the L3 layer. This is where SVI comes in, with SVIs the switch recognizes the packet destinations that are local to the sending VLAN and switches those packets and packets destined for different VLANs are routed. A VLAN is mapped usually to one SVI, also unless the VLAN is created there will be no spanning tree instance running hence the line protocol will be down for the SVI VLAN. Source : Cisco Learning Network.

 
# Already L3 enabled.
ip routing 

# Create VLAN2

cloud10>enable
cloud10#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud10(config)#vlan 2
cloud10(config-vlan)#name servers
cloud10(config-vlan)#exit
cloud10(config)#

# Assign the physical interface to this VLAN.

cloud10(config)#interface fa0/10
cloud10(config-if)#switchport access vlan 2
Command rejected: Fa0/10 not a switching port.
cloud10(config-if)#switchport
cloud10(config-if)#switchport access vlan 2
cloud10(config-if)#end
cloud10#

# Configure Switch Vlan Interfaces (SVI)

cloud10(config)#interface vlan 2
cloud10(config-if)#
*Mar  1 04:00:11.183: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up
cloud10(config-if)#ip address 10.0.1.1 255.255.255.0
cloud10(config-if)#no shutdown
cloud10(config-if)#exit

#Do similar steps for Cloud20 and assign an IP address (same subnet.)

cloud20#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud20(config)#interface vlan 2
cloud20(config-if)#
*Mar  1 04:07:02.166: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up
cloud20(config-if)#ip address 10.0.1.2 255.255.255.0
cloud20(config-if)#no shutdown
cloud20(config-if)#exit


#Configure trunk.

cloud10#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
cloud10(config)#interface fa0/13
cloud20(config-if)#switchport trunk encapsulation dot1q
cloud10(config-if)#switchport mode trunk
cloud10(config-if)#no shutdown
cloud10(config-if)#end
cloud10#

# Verify trunk mode.

cloud10#show interfaces fa0/13 switchport
Name: Fa0/13
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 2 (servers)
Trunking Native Mode VLAN: 2 (servers)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled


cloud10#show interface fa0/13 trunk

Port        Mode             Encapsulation  Status        Native vlan
Fa0/13      on               802.1q         trunking      1

Port        Vlans allowed on trunk
Fa0/13      1-4094

Port        Vlans allowed and active in management domain
Fa0/13      1-2

Port        Vlans in spanning tree forwarding state and not pruned
Fa0/13      1-2


#Verify reachability.

cloud20#ping 8.8.8.8 so 10.0.0.20

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
Packet sent with a source address of 10.0.0.20
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/15/34 ms
cloud20#ping 8.8.8.8 so 10.0.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
Packet sent with a source address of 10.0.1.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/13/17 ms

loud10#ping 8.8.8.8 so 10.0.0.10

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
Packet sent with a source address of 10.0.0.10
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/10/16 ms
cloud10#
cloud10#ping 8.8.8.8 so 10.0.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
Packet sent with a source address of 10.0.1.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/10/17 ms
cloud10#

cloud10#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]